Roland Options

Roland Bulk Conversion

• If converting disk, convert only...
  If you are translating an entire Roland disk, this determines if Translator will convert the entire Performances folder or the entire Patches folder.
  Default: Patch
• Roland->Giga; Bulk Convert into Groups
  Rolands use an effecient method of handling samples on their disks - they use one sample pool. Many Patches or Performances can share references to the same samples - using only one set of data. As a result, many times when you convert a Roland disk, for example if you are converting to GigaStudio format - from a 650mb CD you might wind up with 2mb of data, because the refrenced samples grab the same data over and over again, make redundant copies of the data.
  This option is in effect when you convert a whole disk. It will group Patches or Performances in groups, where the members have the same referenced samples in common. You will wind up with, in the GigaStudio example, with 30-40 large .gig files, maybe 10-20mb apiece. They will have the Patches/Performances that share the same samples - this way there is not much chance of samples being copied more than once. The advantage of this is that you make the best use of your disk space, with the least amount of .gig files as possible.
  Default: Unchecked
• Write Shortcuts for duplicate samples
  Roland disks use whoel large sample pool for the Performances and Patches to draw from; as a result, many objects share samples. When converting, you may be putting the resulting control files into different areas, but you don't want to rewrite the samples just so you can see which samples go with which control files. This option enables shortcuts to be written so you can see what samples are being referenced without rewriting the samples.

Show Partials Folder
Partials are the object that Roland uses to reference samples and store a keyranges parameters. Patches use Partials in a keymap to reference samples. Partials are never intended to be played in and of ttheselves, so there's little use of translating them in and of themselves. Thus. there's not much reason to show them in the Translator interface. Checking this option shows the Partials folder.
Default: checked

Show Object Location Dialog
Partials are the object that Roland uses to reference samples and store a keyranges parameters. Patches use Par

Strip 3-Character Category Preferences
The Roland, for the first 4 characters of an object name, lists a three character code plus a colon. If this option is checked, Translator, when exporting or importing a Roland object, will ignore the first 4 characters and simply name the object as the following 12 characters.
Default: unchecked

Only Strip in cases of 16->12 or 8 Character Truncations
(Only enabled when "Strip" above is checked) If checked, Translator will only strip the category Prefix if it needs to truncate the name down to less than 16 characters; otherwise, it will preserve it.
Default: checked

Disallow translating Label Names
Designers of popular Roland CD-ROM's use many "blank" objects to list categories, in order to make lists more understandable. These are real objects you would load - but they are just blank. If checked, Translator will ignore these type of objects. Unfortunately, the only way to recognize these is to look at the "ID"; that is the three characters that come before the colon (:) in the file name.
Here is the current list of ID's that are considered: "---:" "AAA::" "___:" "===:" "***:"
Default: Checked

Enable Roland Digital Emphasis Filter
Roland's use a special filter on input and output for their samples. Translator simulates this, with three different settings depending on your taste. See the Roland Emphasis/DeEmphasis article in the Miscellaneous section for specifics on these controls.
Default: checked

Drive Label
This is the Drive Label that is written by default to a drive when you format it with Translator, when the Prompt for Drive Label is checked in the Options-General Tab.
Default: "Formatted"

Prevent Performance Compression
Translator, unlike any other transaltion software, converts Roland Performances just as they are set up on the Roland. If two or more "parts" in the Performance share the same MIDI Channel, they will be combined into one conglomerate Program/Preset/Instrument. This is called Performance Compression. If you do not want this to occur, check this option.
Default: unchecked

Do Not Read Disabled Patches In Performances
Many Performances reference more than one Patch, except enable the first one and disable the rest, with the intention tha you toggle what is enabled in order to audition a range of Patches for your liking. When this is checked, these Patches are not read or converted, even into disabled states. When unchecked, the Patches are read and converted regradless of being enabled or not.
Default: checked

Velocity Grid (Fantom Only)
This averages incoming velocity ranges to fit a 16-part grid (out of 128 values). For example, a velocity of 5-90 will become 0-95, and 29-120 will become 32-127. This eases the pressure on the limited Fantom format to accomdate staggered or unusual velocity ranges.
Default: checked

Add Reverb
This enables a default light reverb on the sound when converting into XV-5080 or Fantom formats. Note: the Reverb is always written - this parameter simply enables it to be played within the sound.
Default: checked

Wet/Dry Balance
This is the Wet-Dry balance of the reverb noted above. Note: the Reverb is always written - this parameter simply controls the balance of it WHEN it is enabled.
Default: 10:90

Parameter Tolerance
Roland S-7x and XV-5080 share envelopes, LFO and filter settings for all the velocity ranges within a keyrange, and Fantom's share things on a more general basis. There cannot be unique setttings for every sample reference.
Thus, if incoming references require unique values, Translator is either going to write new Patches that accomodate this (and put them together as a Performance when finished), or you can use the Parameter Tolerence value (in a percent) to "tolerate" certain values and trade off complexity for the convenience of having a single Patch represent your incoming Program, rather than a unweildly Performance.
Default: 0%

Go To Comparison Options button Takes you to the master Comparison Options area (under Options). This is Parameter Tolerence from a different angle - on a parameter set basis, you can choose to ignore incoming values when it comes to comparisons. The Parameter Tolerence value is applied to those parameter sets that are not ignored. Show Comparison Errors The Fantom format, and to a lesser degree the S-7x and XV-5080 formats, are limited formats, and Translator uses many comparison averaging techniques to cram more complicated formats into their structures. This option allows a dialog to come up to allow you to manually control how these comparison averaging functions are applied. This option is handy, not just because it alows you to control the averaging, but it also tells you when a more complicated format is incoming. Default: checked